Quick Detail
Place of Origin
HS-CODE
84-
Package & Delivery Lead Time
Detailed Description
Configuration introduction
一．Computerized unit
1. Memory Zero returning: When closed, The machine can return to the original position automatically after plate-brushing or small-range plate-changing during the operation.
2. reticulate roll with controlled lifting and lowering: Control the reticulate roll not to down when a certain group is not needed printing temporarily, so as not to clean the ink rollers.
3. Automatic paper-aligning: flexible setting for aligning time and interval time , features smooth operation and is suitable for personal operation custom.
4. Position zero returning: Plate position zero returning provides accurate plate equipment at one time, only after two trial printings generally.
二. Feeding( 1 set)( lead edge feeding is optional)
1、 Machine open and close
1）Machine open and close are motorized, moving with continuous alarm, so as to ensure the safety of the operator.
2）Equipped urgent stopping switch between every unit, achieving interior control to stop movement, so as to ensure the safety of inner operator
3）Pneumatic inter-lock device.
4) The whole machine is chiefly locked.
2、Sheet cleaner
1）Sheet cleaner can substantively remove contaminations on the board printings, ensuring high printing quality.
3、Feeding roller
1）upper feeding roller:Φ142.68mm。upper feeding roller
2）Non-sew roll,which is warped with wearable rubber, with dynamitic balance adjustment .
3）lower feeding roller:Φ152.52mm, embossed and chrome plated
4）The clearance between feeding rollers is worn wheel adjusted, with an adjustment range of 0-12mm
4、Upper and lower feeding roller of the second group
1）Non-sew roller, with dynamitic balance adjustment, is warped with wearable rubble.
2）lower roller :Φ152.52mm ,embossed and chrome plated
3）the clearance between feeding roller is manually adjusted, with an adjustment range of 0-12mm。
5、automatic feeding
1）The right and left baffles and rear baffle are all motorized, with an aligning function.
2）Suction assisted kicker feeding system can adjust wind according warp degree
三、Printing unit(1 color,1 set)：
1、Printing roller
1）exterior diameter:Φ320.17mm(exterior diameter with plate:Φ334.57mm)。
2）surface ground and chrome plated。
3）Dynamitic and static balance adjustment, ensure stable running.
4）Fixed ratchet wheel plate shaft
5）Plate-hitching makes an easy and quick plate equipment, and is suitable for plate-hitching bars of 10MM
6）The step-switches in each printing unit control the printing roller turning forward or backward
2、Press roll
1）exterior diameter:Φ152.52mm。
2）Steel roll , surface ground and chrome plated.
3）Balance adjustment, with stable running.
4）the clearance between press rolls are manually adjusted with a graduation display, adjustment scope:0-12mm。
3、Steel reticulate roll (ceramic anilox is optional)
1）exterior diameterΦ196.8mm。
2）The surface of steel roll is specially processed and engraved
3）Consistent net point, even ink layer , lasting and durability.
4）specially processed lines ensure to prolong the life of plate and rubber rolls
4、Rubber roll
1）exterior diameter:Φ182mm。
2）Steel roll is of wearable rubber wrapped.
3）Rubber roll , fine ground with crown , ensuring perfect ink transfer.
5、Phase adjustment
1）Adopts planet gear design
2）Phase indication digital display, make the operation convenient, visual and precise.
2）The printing register adjusted by PLC, touch screen and 360o motorized adjustment（both when running and stop）；with a precision up to 0.15 mm
3）Uses transducer to adjust the phase of plate roll, adjustment at will under dynamic or static state, micro precision up to 0.10mm. reset zero timely when there is a misplace after moving the machine unit, the precision can be up to 0.5mm.
6、Ink circulation
1）Pneumatic diaphragm pump provides the circular ink-feeding，featuring stable ink supply ,easy operation and convenient maintains
2）Ink filter can filtrate the impurity, ensuring perfect products.
7、Printing phase fixing device
1）electromagnetic brake design
8、Axis adjustment mechanism
1）Motorized axis adjustment
2）position indication digital display, make the operation convenient, visual and precise.
四、Slotting unit（1 set）：
1、Scoring wheel
1）axis diameter ;Φ146 mm， surface ground for tow times, and chrome plated, ensuring smooth operation.
2）0-12mm。manual scoring depth adjustment, with a range of 0-12mm
3）scoring wheel adopts superior imported polyaniline.
2、The slotting head transverse adjustment
1）axis diameterΦ154 mm, surface ground for tow times, and chrome plated, ensuring smooth operation.
2）slotting blade width:7mm。
3）Alloy toll steel via heat treatment, the rubbing and saw-tooth blade features superior hardness and tenacity.
4）Alloy steel via heat treatment, grinding blade ,enable to keep sharp edge and high precision.
5）Creasing roll, guiding roll and slotting boss transverse movement motor button synchronously controls
3、Slotting phase adjustment system
1）Planet gear mechanism
2）The front and rear slotting registers adjusted by touch screen, motor button double control and 360o degrees motorized digital adjustment（either when running or stop）.
3）The slotting head is transverse adjusted motorized. （either when running or stop）
五、Die-cutting unit( 1 set)
1． Operation function
1)Under different cases, via partiality device of the cylinder stencil roll and anvil roll can automatically jump off to reduce the hollow load for the machine and prolong the life of anvil roll and cutter.
2) Uses planet gear design to adjust phase within 360 degree, operating under stop, running, front or back, with a precision up to 0.10mm, facilitating plate equipment and plate correction.
3)register indication digital display, make the operation convenient, visual and precise.
4) Mechanical transmission anvil roll can move right or left , with a movement of 30mm. radial differential device can greatly prolong the life of rubber roll through even distribution of abrasion.
5)Anvil roll amendment device can amend the rubber roll time after time .
6) Equipped with waste-removing device on the transmission belt.
2．Mold roll
1) mold roll diameter:Φ290mm(without die-cutting)。
2) Alloy , non-sew steel , surface ground and chrome plated.
3) stencil fixed screw space:axis100 mm; radial 18 mm part。
4) available die-cutting height 23.8 mm。
5)board thickness:16 mm(single wall)；13 mm(double wall)。
3．The rubber mat roll：
1) The rubber mat rollΦ350mm(not including anvil rubber)
2)Alloy , non-sew steel , surface ground and chrome plated.
3) anvil rubber thickness:10 mm. (exterior diameter370 mm)width:250 mm， can be used for 80,000,000 times, generally.
六、Piker(one group)
1、Connection arm
1.) Connection arm can be operated manually or automatically.
2) The transfer belt at the connection arm can be adjusted degree of tightness individually and can choose the number of the arms at will.
2、Bed elevation
1）driven by strong chain
2）stack height up to 1600 mm。
3）The transport bed motor with brake control to keep stable position and anti-slipping
3、Carrier plate
1）The carrier plate is pneumatic driven. The carrier plate will pop-up automatic and hold the coming board when the pre-set height arrives.
2）The back-stopper width is manual adjusted.
3）The flat wrinkle belts avoid the sliding down of board.
七、Transmission gear
1、Main driven gear
1）The gear is made of 20CrMnTi alloy steel, cementite induction hardened with surface ground.
2）The sixth grade precision ( the same grade to car transmission gear), with a hardness of HRC58-62, features smooth operation ,low noise , long serve life, anti-abrasion with ten years, ensuring accurate overprint long lasting.
2、Key connection
1）Using CAPT-LOCKS union link to connect shafts and gears without space when there is a big tensional distance, providing more convenient installment and maintain, higher precision long lasting , and ensuring accurate overprint
八、Main specifications
model 1800×1000 2200×1000 2500×1200 2800×1200
Max machine speed（pcs／min） 160 160 160 160
Max printing speed（pcs/min) 140 140 128 128
Max feeding size（mm） 1800×1000 2200×1000 2500×1200 2800×1200
Min feeding size（mm） 650×250 650×250 650×350 650×350
Max printing area（mm） 1750×950 2150×950 2450×1180 2750×1180
Standard plate thickness （mm） 7.2 7.2 7.2 7.2
Working power（kw） 32（according to printing units) 32（according to printing units) 32（according to printing units) 32（according to printing units)
Total power（kw） 36（according to printing units) 39（according to printing units) 39（according to printing units) 39（according to printing units
0 likes
Click enlarge Image
