High Voltage High Power SMD LED Diode EMC 3030 with 12V 20mA 1.5W

Quick Detail

Package & Delivery Lead Time

Detailed Description

High Voltage High Power SMD LED Diode EMC 3030 with 12V 20mA 1.5W Features: # # P-LCC-2 package. # White package. # Optical indicator. # Colorless clear window. # Ideal for backlight and light pipe application. # Inter reflector. # Wide viewing angle. # Suitable for automatic placement equipment. # Suitable for vapor-phase reflow, Infrared reflow and wave solder processes. # Available on tape and reel (8mm Tape). # The product itself will remain within RoHS compliant Version. Descriptions: # # The TOP3030 series is available in soft red, orange, yellow, green, blue and white. Due to the package design, the LED has wide viewing angle and optimized light coupling by inter reflector. This feature makes the SMT TOP LED ideal for light pipe application. The low current requirement makes this device ideal for portable equipment or any other application where power is at a premium. Applications: # # Automotive: Backlighting in dashboards and switches. # Telecommunication: Indicator and backlight in telephone and fax # Indicator and backlight for audio and video equipment. # Indicator and backlight in office and family equipment. # Flat backlight for LCDs, switches and symbols. # Light pipe application. # General use. - - - - Part No. | Chip Material | Lens Color | Source Color | DL-TOP3030SRC | AlGaInP | Water Clear | Hyper Red | - - - - Absolute Maximum Ratings at Ta=25 - - - - Parameters | Symbol | Max. | Unit | Power Dissipation | PD | 750 | mW | Peak Forward Current (1/10 Duty Cycle, 0.1ms Pulse Width) | IFP | 500 | mA | Continuous Forward Current | IF | 350 | mA | Reverse Voltage | VR | 5 | V | Electrostatic Discharge (HBM) | ESD | 1000 | V | Operating Temperature Range | Topr | -40 to +80 | Storage Temperature Range | Tstg | -40 to +85 | Soldering Temperature | Tsld | 260 for 5 Seconds | - - - - Electrical Optical Characteristics at Ta=25 - - - - Parameters | Symbol | Min. | Typ. | Max. | Unit | Test Condition | Luminous Intensity * | IV | 6000 | 6500 | --- | mcd | IF=350mA (Note 1) | Viewing Angle * | 21/2 | --- | 120 | --- | Deg | IF=350mA (Note 2) | Peak Emission Wavelength | p | --- | 630 | --- | nm | IF=350mA | Dominant Wavelength | d | --- | 625 | --- | nm | IF=350mA (Note 3) | Spectral Line Half-Width | | --- | 20 | --- | nm | IF=350mA | Forward Voltage | VF | 1.80 | 2.20 | 2.40 | V | IF=350mA | Reverse Current | IR | --- | --- | 10 | A | VR=5V | - - - - Notes: # # Luminous Intensity Measurement allowance is 10%. # 1/2 is the off-axis angle at which the luminous intensity is half the axial luminous intensity. # It use many parameters that correspond to the CIE 1931 2. X, Y, and Z are CIE 1931 2 values of Red, Green and Blue content of the measurement. Please read the following notes before using the product: # # Over-current-proof Customer must apply resistors for protection, otherwise slight voltage shift will cause big current change (Burn out will happen). # # Storage 2.1 Do not open moisture proof bag before the products are ready to use. 2.2 Before opening the package, the LEDs should be kept at 30 or less and 90%RH or less. 2.3 The LEDs should be used within a year. 2.4 After opening the package, the LEDs should be kept at 30 or less and 70%RH or less. 2.5 The LEDs should be used within 168 hours (7 days) after opening the package. 2.6 If the moisture adsorbent material (silica gel) has fabled away or the LEDs have exceeded the storage time, baking treatment should be performed using the following conditions. Baking treatment: 605 for 24 hours. # # Soldering Condition 3.1 Pb-free solder temperature profile. 3.2 Reflow soldering should not be done more than two times. 3.3 When soldering, do not put stress on the LEDs during heating. 3.4 After soldering, do not warp the circuit board. # # Soldering Iron Each terminal is to go to the tip of soldering iron temperature less than 260 for 5 seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder. # # Repairing Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing. # # Caution in ESD Static Electricity and surge damages the LED. It is recommended to use a wrist band or anti-electrostatic glove when handling the LED. All devices, equipment and machinery must be properly grounded. FAQ 5. What`s your main products ? LumiS LED Specializes in high quality led from 2011, Inculding EMC 2016/3014/3020/3030 and Ceramic 3535/5050. The Power from 0.2W-10W/LED, The Voltage from 2.8V-50V/LED; CCT from 2500-20000K, also have RGBWY/UV/IR, RGBW 4in1 Hight Power Ceramic LEDs. Also we can customize your LED Module, etc. 6. Do you have any certifications for your products ? Yes, All of led have CE,RoHS certifcations and LM-80 for our EMC Serices Products. 7. What chip you usually use for your led ? We usually use Sanan LED chip.

Basic Company Information

HongKong Double Light Electronics Technology Company

Company Advantage

Detail Company Introduction