Grass-cutting Alloy Saw

Selling Leads Detail

Company Info

 

Number Product Number Specification 1 KGP001 B2multiaperture shutter 230*1.7/1.25*25.4*36T 2 KGP002 B2multiaperture shutter 255*1.7/1.25*25.4*40T 3 KGP003 B2ellipse shutter（HBM) 230*1.7/1.25*25.4*36T 4 KGP004 B2ellipse shutter（HBM 255*1.7/1.25*25.4*40T 5 KGP005 BL 230*1.7/1.25*25.4*36T 6 KGP006 BL 255*1.7/1.25*25.4*40T 7 KGP007 B5ellipse shutter（CNK) 230*1.7/1.25*25.4*36T 8 KGP008 B5ellipse shutter（CNK) 255*1.7/1.25*25.4*40T 9 KGP009 B5L（CNK) 230*1.7/1.25*25.4*36T 10 KGP010 B5L（CNK) 255*3.2/2.5*32*100T 11 KGP011 FSmultiaperture shutter MEX 230*1.7/1.25*25.4*36T 12 KGP012 FSmultiaperture shutter MEX 255*1.7/12.5*25.4*40T 13 KGP013 FSmultiaperture shutter MEX 255*1.7/1.25*25.4*60T 14 KGP014 ZXellipse shutter（HBM) 230*1.7/1.25*25.4*36T 15 KGP015 ZXellipse shutter（HBM) 255*1.7/1.25*25.4*40T 16 KGP016 ZXMmultiaperture shutter（HBM) 230*1.7/1.25*25.4*36T 17 KGP017 ZXMmultiaperture shutter（HBM) 255*1.7/1.25*25.4*40T 18 KGP018 Vellipse shutter（HBM) 230*2/1.25*25.4*36T 19 KGP019 Vellipse shutter（HBM) 255*2/1.25*25.4*40T 20 KGP020 VMmultiaperture shutter（HBM) 230*1.7/1.25*25.4*36T 21 KGP021 VMmultiaperture shutter（HBM) 255*1.7/1.25*25.4*40T 22 KGP022 using for forest（No grinding） 230*2.2/1.25*25.4*50T 23 KGP023 using for forest（No grinding） 255*2.2/1.25*25.4*60T Saw Caution: 1. Please put alloy saw vertically hang the drying rack, be sure to avoid the damp places, do not place alloy saw on the ground or on a shelf,keeping flat will lead alloy blade deformation. 2. Use time, do not exceed the maximum speed. Speed method of calculation is attached for information. 3. Use time, must take protective mask, gloves, helmets,working protection shoes, protective glasses. 4.During the installation Alloy saw, must firstly confirm the function,use of saw table,first read the statement of saw table.Avoid mistakes Install so as to caused the accident. 5.During the installation Alloy saw,must first check whether there is a split distortions, and fill-ping, swaps and other phenomena teeth on alloy saw, and then install it. 6. Super-hard and sharp ofsawtooth alloy saw,prohibit the collision, falling ground, with taking carefully. 7.After install alloy saw blade, the saw core hole must be confirmed whether firmly fixed in the flange of saw table saw, a gasket must be good washer,and then gently hand to push saw blade,confirmed the rotation Whether the eccentric shaking. 8.The cutting direction of Alloy saw arrow must be aimed at rotation direction of saw table.Strictly no installation the opposite direction, the mistake direction will lead out tooth. 9. Pre-turn: the replacement of alloy saw,pre-turn for one minute before the use ,in order to let the saw table into the work status. 10.Before cutting, must confirm whether the use of alloy saw blade is in keeping with the cutting material. 11. Cutting material, it must Qingqingdijiang normal operation of the saw blade intercept material, prohibited Shijinjiangya pushing hard. 12. Prohibit the reverse turn,reverse leads to drop saw teeth, be dangerous. 13.During using, hear unusual voices and see the abnormal shaking, the section is not flat, immediately stop operations and look for unusual reasons.And replace saw . 14.At Cutting, the prohibition of the saw blade to stop suddenly in the middle of cutting. Stop in the middle of cutting,will lead the sawtooth shedding, saw deformation. 15. Pls promptly apply proof-rust oil after cutting.Prevent from saw rust. 16.When the sawtooth is not sharp,pls grind sawtooth again,must go to the manufacturers specify or professional grinding shop. Otherwise it will destroy the original sawtooth angle,impact accuracy cutting and shorten the life of saw blade use.

Basic Company Information

XiaMen ZhongJu Hardware Tool Co.LTD.

Company Advantage

Detail Company Introduction