Corrugation 125mm x 25mm
Characteristic of galvanized steel helical spiral corrugated culvert
Specification
Pipe diameter: 300-2500mm
Length: 1-12m
Thickness: 1.6-3.2mm
High strength
It with more than 1.5 times compression strength than the concrete pipe because of the corrugation structure
Easy for transport
The weight of the spiral corrugated culvert is only 1/10~1/5 of same size concrete pipe, even can be carried by people without machine.
Install in shorter time
The spiral corrugated culvert is connect by clamping band or flange, and the length can be make according to the customers’ request, then easy to install, and can be installed in shorter time.
Long service life:
The spiral pipe corrugated culvert adopt 300-600g/m2 galvanization steel plate, normally its servise life is 50-100 years, if in the strong corrosion environment, painting asphalt on the in and out surface of the pipe, can enlong 20-50 years based on the normal service life.
Economic
The standard length is 6m, simple connection, shorter working time. Because it is light, easy for transport, with few foundation construction, lower fee on drain pipe. For example, we make comparison on steel corrugated culvert pipe and concrete pipe in diameter 800mm, spiral pipe corrugated culvert is only need about 90% if concrete pipe fee, and it can save cost of forklift, crane, and other machines when the transport is not good.
Cross section shape and size of galvanized steel helical corrugated culvert pipe
Normally, the cross section is round shape, corrugation is 68X13mm, 125X25mm
Application of helical corrugated steel culvert pipe
The helical spiral pipe corrugated culvert is used in municipal drainage,building outside drainage, farm drainage, industry drain system, also adopt in road and railway closed conduit or culvert, shell of vertical pile, rain water collection, etc
Drainage: domestic sewage, golf course drain, underground garage, factory drain, factory, airport water drain.
Culvert: drain-pipe under the road, higher cross drain-pipe, underground culvert of railway, small tunnel, closed conduit, small bridge.
Protection shell: underground communication cable, protection pipe for gas pipe， also can be adopted on construction site, and protection shed, etc
Industry: air conduit for gas in coal mine (negative pressure)
Farm: driven well wall for farm, invert siphon for irrigation, farm water drain.
Structure
Spiral corrugated culvert is treatment by galvanized steel belt spiral seaming joint
The diameter is smaller than 1m, adopt corrugation 68X13mm, each section standard length is 6m, diameter is bigger than 1m,adopt corrugation 125X25mm, each section standard length is 6m, and can make difference size as per clients’ request±±±±
Corrugated culvert pipe connection by two or more pieces of clamping band or flange, inlay PE plate or sealant or rubber gasket, fasten by high strength bolts.
Material
The steel plate is DX52D or SGHC, chemical and mechanical property should be accord with EN10327 or JIS G 3302-2010, steel plate size tolerance should be accord with GB/T-709
Clamping band and angle steel material is Q235, chemical and mechanical property should be accord with GB/T700
Clamping band or angle steel fastener need to adopt high strength bolts, nuts, the grand should be or higher than 8.8, its property should be accord with GB/T1231
Corrugated pipe adopt hot galvanized steel belt for forming, or after forming then hot galvanization treatment.
Appearance
Clean, smooth, and the zinc coating uniformity.
Clamping band request
Connect pipe sections by clamping band, keep the pipe sections point at pipe sections, prevent separate, the bottom permeate or the filling back material permeate.
Drawing 3 classic clamping band system
When assemble the clamping band, lap over connect to each pipe section equally.
When fastening, the length and width of the part which over lap to the pipe have to can bearing the tightening force.
When assemble the clamp band, make sure the gap between two pipe section can be more than 25mm.
Clamp band width is 440mm
(remarks: normally, the clamp band is two pieces, for the big diameter, maybe need 3 pieces or more)
Angle steel connection request
Angle steel adopt Q235 steel
Flange is made by bending the angle steel, manual electric-arc welding and drilling holes.
Corrugated pipe welding angle steel flange adopt manual electric-arc welding.
Spiral corrugated culvert both end welding flange.
Inner diameter is 1m or smaller than 1m, the pipe flange edge is in length 56mm, thickness 6mm equal-sided angle steel, other flange adopt in edge length 70mm, thickness 6mm equal-sided angle steel, for the big pressure, adopte width 70mm, thickness 6mm flat steel.
After welding flange, the inside and outside welding seam painting Dacromet under normal temperature.
Spiral corrugated pipe apply to the municipal engineering drainage pipe, and engineering decoration, etc.
|
wall thickness Diameter
|
1.6mm
|
2.0mm
|
2.8mm
|
3.5mm
|
4.2mm
|
|
|
1200mm
|
● Min:0.5
Max:17
|
● Min:0.5
Max:23
|
● Min:0.5
Max:31
|
● Min:0.5
Max:35
|
|
|
|
1400mm
|
● Min:0.5
Max:15
|
● Min:0.5
Max:19
|
● Min:0.5
Max:28
|
● Min:0.5
Max:36
|
|
|
|
1500mm
|
● Min:0.5
Max:13
|
● Min:0.5
Max:13
|
● Min:0.5
Max:23
|
● Min:0.5
Max:30
|
|
|
|
1600mm
|
● Min:0.5
Max:12
|
● Min:0.5
Max:16
|
● Min:0.5
Max:21
|
● Min:0.5
Max:31
|
● Min:0.5
Max:35
|
|
|
1800mm
|
● Min:0.5
Max:11
|
● Min:0.5
Max:15
|
● Min:0.5
Max:20
|
● Min:0.5
Max:26
|
● Min:0.5
Max:28
|
|
|
2000mm
|
● Min:0.5
Max:10
|
● Min:0.5
Max:13
|
● Min:0.5
Max:18
|
● Min:0.5
Max:23
|
● Min:0.5
Max:28
|
|
|
2200mm
|
● Min:0.5
Max:9
|
● Min:0.5
Max:12
|
● Min:0.5
Max:16
|
● Min:0.5
Max:21
|
● Min:0.5
Max:26
|
|
|
2400mm
|
●
|
●
|
●
|
●
|
●
|
|
|
2700mm
|
●
|
●
|
●
|
●
|
●
|
|
|
3000mm
|
|
●
|
●
|
●
|
●
|
|
|
3300mm
|
|
|
●
|
●
|
●
|
|
|
3600mm
|
|
|
|
●
|
●
|
|
|
Tips: 1.the data of sheet means depth of fill, named min and max; 2.different diameter, thickness,length and other size are available, accroding to your requirement.
|
|
| |
China [CN] 
Click enlarge Image