1. Description of rtv 2 liquid silicone rubber for frame gypsum molds
C830 silicone rubber is condensation cure silicone rubber (tin cure silicone rubber) for mold making. The silicone rubber will be cured under room temperature. It's two components, the mixing ratio is 100:2. Part A is a flowable liquid silicone, part B is the catalyst. It has an exceptional fluidity and good operability.
2. Characteristics of rtv 2 liquid silicone rubber for frame gypsum molds
* An exceptional fluidity and good operability, easy to demold* Good tensile strength and tear strength* Suitable hardness* Copy detailed pattern * Good flexibility
* Eco-friendly
* Long shelf-time &lifetime
3. Application of rtv 2 liquid silicone rubber for frame gypsum mold
C830 liquid silicone rubber is perfect molding material, it is suitable to make mold for concrete casting, artificial stone, brick, cement casting, gypsum decorations, plastic product, resin craft, polyester, polyurethane, bronze casting, statues, jewelry, wax, crystal, tire mold, shoe mold, clay casting, ceramic casting. etc.C830 liquid silicone rubber is mainly suitable for small or middle sized products with delicate pattern by pouring and brushing operation.
4. Datesheet of rtv 2 liquid silicone rubber for frame gypsum molds
|
Item
No.
|
Hardness
(shore A°)
|
Viscosity
(CPS)
|
Tensile-strength
( kgf /cm2 )
|
Tear-strength
(kgf /cm2 )
|
Elongation-break(%)
|
Mixing
ratio
|
operation time (25 ℃ )
|
Curing
time ( 25 ℃)
|
shrinkage
|
|
C830
|
30±1
|
22000±1000
|
≥42
|
≥26
|
≥420
|
100:3
|
20-30 mins
|
2~3 h
|
≤0.3%
|
5. Using instructions of rtv 2 liquid silicone rubber for frame gypsum molds
Step 1: Prepare and clean the prototype.
You must make sure your original molds perfect, fix the original mold on a board, then using some assistant material (like cardboard) to make a frame for to surround the prototype. The frame is no need, if we make the mold by brushing way.
Step 2: Take the silicone and catalyst as the ratio 100:2 (silicone : catalyst= 100:2), mix the silicone rubber and catalyst evenly.
Notes: rtv silicone rubber is a kind of flowing liquid and it contains two parts. Part A is a kind of flowing liquid and part B is the curing agent. Remember to mix part A and part B evenly, otherwise the silicone rubber will be partly solidified and this will bring troubles for your final operation. What's more, the finishes molds will have a short life. All of these will cause a waste of silicone rubber.
Step 3: Vacuum pumping.
After mixed the silicone evenly, it is better to release the bubble by vacuum pumping.
Step 4: Pouring cast or brushing cast.
After released the bubble, we can pour/brush the silicone rubber on the prototype.
Notes: Please finishes all the steps within the operation time. If not, it will cause cross linking reaction, and no more further steps will be available. So, we have to pay attention to the pot life and curing time.
6. Package and shelf life of rtv 2 liquid silicone rubber for frame gypsum molds
Package
1kg/drum,5kgs/drum,20kgs/drum,25kgs/drum,200kgs/drum.
Shelf life and transportation1. Twelve(12) months when stored at 25C in tightly closed original packages.2. This kind of product is non-dangerous product, which could be transported as general chemicals.
Any inquiry, feel free to contact Ms. Rachel:
Email:rachel(at)gcsilicone(dot)net
skype:13929247235
Mobile/whats app:86-13929247235
Tel:86-0769-88020535
Website: www.gcsilicone.en.alibaba.com
China [CN] 
Click enlarge Image